Toshiba / Canon Medical CT error codes
168 GTS (Gantry + Table System) status codes for the Activion16 (TSX-031A) and the Aquilion family — each with its meaning, severity, and the subsystem that reports it.
CPU Board (Themis) — Thermal Protection · 1
MEC Board — Board Test · 1
Print Drum Module — Position Sensors · 6
HC10814Drum passed sensor S24 not connected or malfunctioningHC10815Drum entry sensor S23 not connected or malfunctioningHC10816Drum reference position sensor S8 not connected or malfunctioningHC10827Drum home position sensor S1 not connected or malfunctioningHC10828Drum 14-inch print-position sensor S2 not connected or malfunctioningHC10830Drum 10-inch print-position sensor S3 not connected or malfunctioning
Firewire Link (Crius–Themis) · 2
MEC Board — Power Supply Rails · 2
MEC Board — Connector Detection · 9
HC11006Connector P21 not detected on the MEC boardHC11007Connector P27 not detected on the MEC boardHC11008Connector P28 not detected on the MEC boardHC11009Power supply has no serial connection to the MEC boardHC11010Connector P29 not detected on the MEC boardHC11011Connector P30 not detected on the MEC boardHC11012Connector P31 not detected on the MEC boardHC11013Connector P34 not detected on the MEC boardHC11014Connector P35 not detected on the MEC board
Film Pick-up Module — Vacuum Pump (M13) · 1
CPU Board (Crius) — Board Test · 1
CPU Board (Crius) — Battery RAM Test · 1
CPU Board (Crius) — RAM Test · 1
Alignment Module — Home Position Sensors (S5/S6) · 3
Alignment Module — Entry Sensor (S22) · 5
HC10826Alignment module entry sensor S22 not connected or malfunctioningHC11211No sheet detected at alignment entry sensor S22 after horizontal transport (input jam)HC11213Sheet did not clear alignment entry sensor S22 in time (input jam)HC11233Alignment entry sensor S22 activated continuously during start-up or empty checkHC11234Alignment entry sensor S22 triggered unexpectedly during start-up or empty check
Alignment Module — Alignment Motors (M7/M8) · 2
Alignment Module — Film-Format Solenoid (EM2) · 1
Alignment Module — Transport Jam / Time-out · 1
Cover-Open & Jam-Clearance Switches · 3
CPU Board (Crius) — Thermal Protection · 1
CPU Board (Themis) — Board Test · 1
CPU Board (Themis) — RAM Test · 1
Print Drum Module — Drive Motor & Mechanics · 4
Thermal Head Module — Positioning Mechanics · 2
Print Section — Film Jam & Transport Sensors · 8
HC11207No sheet detected at drum entry sensor S23 after alignment — jam in print sectionHC11212Drum entry sensor S23 prematurely activatedHC11215Sheet fails to clear drum entry sensor S23 within time-out — internal jamHC11216No sheet detected at drum passed sensor S24 during printing — internal jamHC11217Sheet not caught by drum-TPH closure at drum entry sensor S23HC11235Drum entry sensor S23 continuously activated at startup or empty-checkHC11236Drum entry sensor S23 triggered during startup or empty-checkHC11237Drum exit sensor S24 continuously activated at startup or empty-check
Calibration & Sensitometry Files · 3
Film Tray Module — Sensitometry Calibration · 3
Film Tray Module — Print-Disable Override · 3
Film Tray Module — Tray Disabled · 3
Film Tray Module — All Trays Disabled · 1
Film Tray Module — MDM Calibration · 3
MDM Module — Densitometer (DSH) Self-Test · 1
MDM Module — Light Sensor · 1
MDM Module — Home Position Sensor (S7) · 1
MDM Module — Lamp / Light Sensor · 1
MDM Module — Scan Motor (M11) · 1
MDM Module — Output Takeover Motor (M9) · 1
MDM Module — Densitometer (DSH) Board Link · 1
MDM Module — Light Intensity Calibration · 1
MDM (Macrodensitometer) Module — Stray Light Detection · 1
MDM (Macrodensitometer) Module — Home Position · 3
MDM (Macrodensitometer) Module — Measurement / Calibration Scan · 1
MDM (Macrodensitometer) Module — Initialization / Calibration · 1
MDM (Macrodensitometer) Module — Sheet Transport (Coversheet Sensor S18) · 1
MDM (Macrodensitometer) Module — Sheet Positioning for Calibration Scan · 1
MDM (Macrodensitometer) Module — Takeover Mechanism · 1
MDM (Macrodensitometer) Module — Handoff to Sorter · 1
Output Sorter Module — Position Sensors · 6
HC10823Sorter exit sensor S27 not connected or malfunctioningHC10831Sorter entry sensor S25 not connected or malfunctioningHC10832First output tray position sensor S31 not connected or malfunctioningHC10833Second output tray position sensor S30 not connected or malfunctioningHC10834Third output tray position sensor S29 not connected or malfunctioningHC10835Fourth output tray position sensor S28 not connected or malfunctioning
Output Sorter Module — Transport Motors · 3
Output Sorter Module — Jam / Timing Faults · 3
Output Sorter Module — Entry/Exit Sensors · 3
Film Tray Pick-up (Lower) — Suction & Position Sensors · 2
Film Tray Pick-up (Lower) — Passed Sensor S20 · 2
Film Tray Pick-up (Upper) — Suction & Position Sensors · 1
Film Tray Pick-up (Upper) — Passed Sensor S19 · 2
Film Tray Pick-up (Front Section) — Exit Detection Sensor S21 · 2
Film Tray Pick-up (Front Section) — Passed Sensor S21 · 2
Film Tray Pick-up (Middle) — Passed Sensor S19 · 1
Film Tray Pick-up — Jam & Suction Timing · 2
Film Tray Pick-up — Sensors, Motors & Actuators · 13
HC10836Middle magazine empty sensor S12 failureHC10808Lower magazine empty sensor S13 failureHC10807Middle pick-up passed sensor S19 failureHC10810Lower pick-up passed sensor S20 failureHC10812Lower pick-up module home-position sensor S17 failureHC10813Lower pick-up module pickup-position sensor S18 failureHC10821Pick-up module magazine lock-position sensor S9 failureHC10917Lower pick-up motor M5 failureHC10918Film magazine locking solenoid EM1 failureHC10921Upper pick-up vacuum valve V1 failureHC10922Lower pick-up vacuum valve V2 failureHC11019Lower-tray tag reader failureHC11021Middle-tray tag reader failure
Power Supply Module — Self-Test & Thermal Protection · 3
Power Supply Module — Self-Test / Rail Voltages · 2
Drum Module — THIB Ambient Temperature Sensor · 1
MEC Board — Ambient Temperature Sensor · 2
Power Supply Module — Over-Temperature Protection · 1
Crius Board — Local I/O (Hard Disk) · 1
Crius Board — Local I/O (Floppy Drive) · 1
Crius Board — Local I/O (Key-Pad) · 1
Network — Alarm E-Mail · 1
Network — IP Address Configuration · 1
System Initialization — Homing Timeout · 1
Installation Completeness — System Date Check · 1
Installation Completeness — Print Count Check · 1
TH Module — Power Voltage Rail · 3
TH Module — Resistance Calibration · 1
TH Module — Heater & Cooling Fan · 3
TH Module — Connectivity (TH ↔ THIB ↔ MEC) · 6
HC10914Thermal printhead data/power connector not connected or resistor bank defectiveHC10915Thermal printhead thermistor connector not connected or thermistors defectiveHC11015Thermal printhead data line 1 (P1 to MEC P22) connectivity faultHC11016Thermal printhead data line 2 (P2 to MEC P23) connectivity faultHC11017No connection detected between MEC and THIB boardsHC11020No power connection detected between THIB and thermal head