DryStar 5300 service procedures & guides

104 field-service procedure previews for the Agfa DryStar 5300 — what each procedure does, tools/parts and safety. The full step-by-step lives in the FSELIB service manual.

Calibration · 8

Perform CDM (internal densitometer) calibration7 steps Perform density reproduction check5 steps Check for dust stripes and perform TPH cleaning procedure7 steps Performing the Film Calibration Procedure3 steps Perform Film Calibration4 steps Perform horizontal film alignment procedure7 steps Perform Print Head (TH) Calibration5 steps Perform TH Resistor Check2 steps

Diagnostics · 29

Performing the Acceptance Test3 steps Blank LCD Display0 steps Bubbles0 steps Contouring Visible; 'Landscaping'0 steps Contrast and/or Sharpness Not Okay0 steps Density Reproduction Not Okay0 steps Dmax Too High or Too Low0 steps Dmin Too High1 steps Dust Particles in the Film0 steps Dust Particles on the Print Drum3 steps Dust Stripes2 steps Message "Error System Failure"3 steps Film Curl0 steps Film Jam Message — Diagnosis and Clearing Procedure3 steps Images Are Not Shown in the Printer Queue0 steps Line Artifacts < 1mm0 steps Line Artifacts Vertical to the Transport Direction (Banding / Transport Shocks)3 steps Display Message: MODXX - Please Replace Module3 steps Message "New Maintenance" (M1-M8)0 steps Optimal Perceivable Levels Not Okay0 steps Pinholes0 steps Printing Diagnostic and Test Images5 steps Keypad Shows "Please Wait - Selftest Proceeding" for More Than 5 Minutes8 steps Sporadic Banding - Pickup Motor Homing (SW Fix)1 steps Surface Artifacts (Scratches)3 steps Surface Artifacts ("Blemish")6 steps TH Driver Banding, Drop & Intermittent Drop3 steps Line Artifacts > 1mm (mm/Macro TPH Banding)0 steps Wide Bands with Lower Density at Left/Right Hand Side of the Film2 steps

Electronics · 9

Replace the compact flash card0 steps Replace the keypad & display module0 steps Replace the main board cooling fan18 steps Replace the main board (VILIS - Themis)20 steps Replace the OSB switch board12 steps Replace the power supply16 steps Replace the safety switch17 steps Replace the TPH cooling fan18 steps Replace the TPH flat cable30 steps

Film transport · 7

Loading Film into the Input Tray10 steps Adjusting the Film Positioner Unit to 11x14 Inch9 steps Replace the Extension cable block module11 steps Replace the Input block module7 steps Replace the Input tray10 steps Replace the Output module0 steps Replace the Pick up module8 steps

Interface · 4

Image Adjustment Workflow and the Connectivity Release Document4 steps Adjusting Contrast and Sharpness at the Modality6 steps Setting Up Logical Printers (DICOM Print SCP)2 steps Setting Up the Printer-Modality DICOM Connection0 steps

Installation · 5

Pre-Installation Planning Checklist12 steps Installation Prerequisites, Positioning and Cable Connection11 steps Security & Privacy Setup (HIPAA, optional)5 steps Installation Site Readiness Checklist (Sign-off)9 steps Removing Transport Protection Locks - Detailed Steps11 steps

Overview · 7

Completing Installation: Customer Instruction and Settings Backup5 steps Replace the air filter6 steps Replace the front cover9 steps Replace the left side cover0 steps Replace the output tray cover17 steps Replace the right side cover10 steps Replace the top cover module13 steps

Print engine · 6

Replace the Cam shaft drive15 steps Replace the Drum drive module10 steps Replace the Input sensors module25 steps Replace the Main drive pulley & Drum belt13 steps Replace the Print drum module2 steps Replace the Thermal print head unit12 steps

Software · 29

ADVP — DICOM Test Tool6 steps Printer Bootup-Message via HyperTerminal12 steps Emergency SW Installation on a New, Empty Internal CF Card6 steps Emergency SW Installation on a Printer in "Error - System Failure" State4 steps Entering Site Data0 steps Adjusting Image Quality at the Printer (LUT, Interpolation, Dmax)6 steps Infocounter — Purpose and How to Access It (Report vs. Service Command Session)12 steps Printer Installation Wizard Walkthrough3 steps Key-Operator Menu on the Local Keypad4 steps How to View the Logfiles Offline (PIDEX Tool)4 steps Show Error Codes (Local Display and Web Pages)0 steps Required Information for the Support Center8 steps Test Image SMPTE2 steps Test Image STI10 steps Test Image STI22 steps Test Images: Medical_Image, LinCheck and TQ-180 steps Software Update via CF Card4 steps Software Update via a Remote Computer5 steps Back up Machine Specific Data after the upgrade2 steps Connect the Service PC to the Drystar 5300 (network or crossed cable) and adapt the PC IP address0 steps Show the customer the new features and hand over updated manuals4 steps Recover from a Failed Upgrade — Emergency Software Installation (Printer in "Error - System Failure")7 steps Perform the SW 2.0.0_C1 upgrade via browser (Service Engineer Command Session, alternate path)10 steps Perform the SW 2.0.0_C1 upgrade via CF card (regular path)11 steps Post-upgrade — print test images, compare before/after, adjust contrast and sharpness if needed9 steps Post-upgrade — confirm new SW version and re-run film calibration4 steps Pre-upgrade baseline — record interpolation settings, film calibration, print reference test images13 steps Prepare for SW 2.0.0_C1 upgrade — copy release to CF card, verify current version4 steps Connecting the Service PC to the Web Pages (Network, IP and Proxy Setup)0 steps