GE X-ray R&F — field troubleshooting
3,432 field-service issues · page 2 of 43
Symptom, error message and equipment context for each GE X-ray R&F issue are public — the full cause analysis and step-by-step resolution are available to FSELIB subscribers.
- Def8000 Wallstand only system, the "table" e-stop function is not satisfied since the E-stop loopback connector was not installed.X-ray R&F
- Definium 8000 Detector not ready after rebooting since the proper warm up time had not passed.X-ray R&F · 1211002
- Revolution XRd Sun workstation locked up during exam due to the Browser not responding.X-ray R&F
- Revolution XRd2X Customer wants to perform reject analysis on repeat exams, but this function is not available on the XRd2X system.X-ray R&F
- P500D Software error corrected by a system reset.X-ray R&F · 1100003, 5000051
- AMX4 AMX4+ Error 45E due to the 2KHZ PHASE 1 and 2KHZ PHASE 1 signals not leaving the CPU boad.X-ray R&F
- Precision 500D Need to send images to PACS with edge enhancementX-ray R&F
- AMX4+ getting reset when taking exposureX-ray R&F
- P500D Transverse Detent Failures with a Grinding Noise due to a twisted belt on the OTS Lateral Feedback Potentiomenter Assembly.X-ray R&F
- AMX4+ AMX700 The tube lock down switch is intermittent, periodically the latch will not release.X-ray R&F
- Revolution XRd Exposure hold to Wallstand due to a loose longitudinal potentiometer gear.X-ray R&F
- XRd System Lock up during boot due to excessive dust in the AWS WorkstationX-ray R&F
- Definium AMX700 Detector image has wide bar at right and bottom sideX-ray R&F
- Definium 5000 Communications problems between CRIB and Magic due to incorrect location of Crib Serial Cable.X-ray R&F
- Definium 5000 Crib serial cable identification can be confusing since multiple names are used for the same cable.X-ray R&F
- Proteus XRa Console KV and MA display blank, error 90-0703 - watchdog, asian interface board resetting due to damaged Collimator CAN BUS Cable.X-ray R&F
- Definium 8000 OTS dead - multiple long and can errors 1090451, 1090453, 1090440, 1090487, 1090489 due to Long Drive Asm failure.X-ray R&F · 1090453, 1090440
- Precision RXi Erratic AEC exposures due to grounded ion chamber.X-ray R&F
- Precision MPi Getting a 0 Relay error on the positioner readout which indicates that a joystick one of the consoles is activated.X-ray R&F
- Precision 500D Bar Code Scanner will not populate any of the fields when scanning bar codes due to improper set upX-ray R&F
- Definium AMX 700 PCs have failed in manufacturing and in the field with a burned up USB port driver chip due to static discharge.X-ray R&F
- Definium AMX700 Unit drives in slow speed only due to a defective Detector Park SwitchX-ray R&F
- PACS The image burned to a CD via PACS is inverted when compared to the original modality image.X-ray R&F
- Revolution XRd AWS 3 and AWS 5 errors due to a hung AWS media converter.X-ray R&F
- MVP3 Errors 162, 172 and 173 reported at power on after the CPU board was replaced.X-ray R&F
- Definium 8000 System fails to aquire a raw or processed image when making an exposure to the wall detector due to a failed NIC in the Magic PC.X-ray R&F
- Definium 5000 Keyboard connected to the embedded Definium 5000 PC does not respond; incorrect type of keyboard used.X-ray R&F
- Precision MPi Intermittent loss of radiographic spot exposure, resulting in blank spot images (black or white depending on doc pref) on INFIMED digital acquisition system.X-ray R&F
- Precision RXi Customer cannot login at digital workstation, defaults to SERVICEAPP as user and expects a password unknown to operator.X-ray R&F
- Precision RXi Shortly after startup, Error 052/062 when collimating table tube with joystick.X-ray R&F
- Proteus System is powered on but Console is OFF due to a defective X1 relay in the PDUX-ray R&F
- Definium 8000 Auto positioning collisions between cable harness and OTS covers due to improper calibration.X-ray R&F
- PRESTIGE VH AD, AK and 2X-ray R&F
- USB bootable jump drive creation for use with Jedi asian, mammocom, dos based programsX-ray R&F
- Precision MPi Time displayed on monitor above gantry is incorrect.X-ray R&F
- Compatibility of 32cm II power supply TH7195-4X-ray R&F · 2178938
- Custom IP Looks do not restore from Backup CDX-ray R&F
- Replace OTS Column Cable Assembly - 5135699X-ray R&F · 3601193
- Custom auto positions do not workX-ray R&F
- Definium 5000 touch sceen display is blank when the system is powered upX-ray R&F
- Precision RXi Unable to locate part number for the AEC I/F bdX-ray R&F
- Definium 5000 Unable to reassemble Embedded PC after replacing Compact FlashX-ray R&F
- P500D and Digital Rad ProductsX-ray R&F · 2362753
- Revolution XRd Gipeto and XQi Image Processing times are not documented in formal documents.X-ray R&F
- It is difficult to find the printer configuration for the AGFA Drystar 5500 Printer.X-ray R&F
- The AMX 4 /AMX4+ documentation is difficult to find the expected mA & kVp voltages and command voltages.X-ray R&F
- Definium AMX700 Mobile Detector has failed.X-ray R&F
- Revolution XRd and XRd2X Replacement X-Ray Tubes and Lead Port CupX-ray R&F
- Digital Rad Error 6D00 on Advantx-E console.X-ray R&F
- The Gipeto and Lightning wall stand vertical drive parts are no longer available due to obsolesense.X-ray R&F · 5179979
- If the incorrect bucky is installed, the cassette center will be 1/2 inch off center.X-ray R&F
- Older style sting driven buckies lacked service documetation for the electrical connections.X-ray R&F
- Xray tube filament is a needed piece of data.X-ray R&F
- HP Magic PC units XW 8200, XW8400 and XW6400 diagnostic tones and leds are not in the current service documentation but can be found on the enclosed web sites.X-ray R&F
- Precision 500D Aurora system No Fluoro Exposure, no image on the fluoro monitor due to the RT bus cable.X-ray R&F
- Definium AMX 700 Detector does not power on.X-ray R&F
- Definium 8000 System operation slow, mouse not responding.X-ray R&F
- Precision 500D Touch screen does not respond to touch.X-ray R&F
- Advantx Erratic shutter operation Adjust motor and gear for proper meshX-ray R&F
- Are the two versions of the P500D 32cm Image Intensifier Power Supplies interchangeable?X-ray R&F · 2178938
- Precision 500D Exposure switch not enabled Cycle PREP/EXP switch - replace switch assembly if necessaryX-ray R&F · 5200040
- Precision 500D Blank image on monitor due to incorrect selection of A/B video switchX-ray R&F
- No PREP - error 458 when attempting to expose due to a defective rotor board.X-ray R&F
- Precision 500D Aurora TUBE SPITS ON P500D AURORA DUE TO THE 3RD LEG OF THE 480 VAC NOT CONNECTED.X-ray R&F
- AMX4 AMX4+ KV’s are shooting 10 KV HIGH during calsX-ray R&F
- Definium AMX 700 - Intermittently some exams are not present on WORKLIST after refresh.X-ray R&F
- Definium 8000 Image Quality on Stryker PACS display device due to limited capabilities of the PACS.X-ray R&F
- AMX4 AMX4+ System is loading down LVLE power supply due to a pinched wire.X-ray R&F
- Precision 500D No power to the IR Remote.X-ray R&F
- Troubleshooting an E1 Error on the Advantx ASC CPU BoardX-ray R&F
- Troubleshooting an E2 Error on the Advantx ASC CPU BoardX-ray R&F
- Troubleshooting an E3 Error on the Advantx ASC CPU BoardX-ray R&F
- Troubleshooting an E4 Error on the Advantx ASC CPU BoardX-ray R&F
- Troubleshooting an E5 Error on the Advantx ASC CPU BoardX-ray R&F
- Troubleshooting an E6 Error on the Advantx ASC CPU BoardX-ray R&F
- Advantx ASC CPU error E8X-ray R&F
- Troubleshooting an E9 Error on the Advantx ASC CPU BoardX-ray R&F
- Advantx ASC CPU error EAX-ray R&F
- Precision 500D Aurora Troubleshooting Intermittent No Sensor Feedback, Error 3800105.X-ray R&F · 3800105
- What are the Service passwords for Definium 5000?X-ray R&F
Full cause & resolution for every GE X-ray R&F issue
Unlock the complete cause analysis, step-by-step resolutions and attached service documents — re-authored, web-first, searchable.
Start free trial7-day free trial · no credit card required