What should a field engineer do about C003000D?

A bad drive was found during RAID configuration. Identify it from the per-slot LEDs on the RDD front panel, replace it using the disk-replacement procedure, then re-run RDD Setup and reconfigure the RDD with parity.. Isolate the RDD (Raw Data Disk Array) subsystem and follow the status-code troubleshooting in the service manual. FSELIB documents the full diagnosis and remedy for the Aquilion RX / V4-62R004 / V3.20R003 / Aquilion ONE / V4.2 / Aquilion S16 / Asteion Super4 / Aquilion 16.

Alarm — high severityRDD (Raw Data Disk Array)

C003000D — Bad disk detected while configuring the RDD RAID

Q: What is Canon Medical (Toshiba) CT error code C003000D?

Bad disk detected while configuring the RDD RAID. It is reported by the RDD (Raw Data Disk Array) — RAID status, reported via RTM on Aquilion RX / V4-62R004 and V3.20R003 and Aquilion ONE / V4.2 and Aquilion S16 and Asteion Super4 and Aquilion 16 CT systems. Severity: Alarm — high severity; subsystem: RDD (Raw Data Disk Array).

Canon Medical (Toshiba) CT error code, reported by the RDD (Raw Data Disk Array) — RAID status, reported via RTM.

What C003000D means

On Aquilion RX / V4-62R004 and V3.20R003 and Aquilion ONE / V4.2 and Aquilion S16 and Asteion Super4 and Aquilion 16 CT systems, status code C003000D indicates: Bad disk detected while configuring the RDD RAID. The code originates in the RDD (Raw Data Disk Array) section of the RDD (Raw Data Disk Array) — RAID status, reported via RTM. Severity level A1 (Alarm — high severity).

Reported action: A bad drive was found during RAID configuration. Identify it from the per-slot LEDs on the RDD front panel, replace it using the disk-replacement procedure, then re-run RDD Setup and reconfigure the RDD with parity..

Toshiba/Canon Aquilion RX (V4-62R004), V3.20R003, Aquilion ONE (V4.2), Aquilion S16, Asteion Super4 and Aquilion 16 CT systems, on the RDD (Raw Data Disk Array) — the fibre-channel raw-data disk array, run as a RAID set with parity, that stores the raw scan data preprocessed by the MHR boards before reconstruction — reported under the RTM (real time manager) RDD device group of the system error message table.

Full troubleshooting for C003000D

The complete diagnosis, cause tree, and step-by-step remedy for the RDD (Raw Data Disk Array) subsystem are documented in the FSELIB Activion16 (TSX-031A) service manual — re-authored, web-first, with real figures.

Open the Activion16 service manual

Related RDD (Raw Data Disk Array) codes

4003000BRDD (raw data disk array) fault reported by the RTM C0030004RDD disk error during a drive command C0030005RDD RAID configuration error or broken disk C0030006RDD rejected a bad command parameter C0030007RDD received a command at the wrong time C0030008RDD RAID configuration file (RAID_CONFIG) missing C0030009Not enough good disks for the RDD RAID to function C003000ARDD RAID cannot run with disks of different types

Related service procedures

Run the console malfunction-diagnosis program (hwtest)Console (Diagnostics)Run the independent MHR PWB test (diagnostics) from the RTM terminalConsole (Diagnostics)Remove the host PC unit (PX74-07959 GR-1/GR-2)Console (Operation)Remove the host PC unit (PX74-08766 GR-1/GR-2)Console (Operation)Remove and install an RDD disk/power-supply unit (Rorke Data)Console (Recon)Remove and install an RDD fan unit (Rorke Data)Console (Recon)

Discuss C003000D with other field engineers in the FSELIB forum

Source: Toshiba/Canon CT service error message table (errmsg.eng, set 102 — Device RTM RDD): "Error in RDD. (Bad disk detected when configuring RAID.)". Reference information re-authored by FSELIB — not a copy of the OEM manual.