Skip to main content
ProcedurePowerPreventive MaintenanceClean

Clean the large-current slip ring

Clean the gantry's large-current slip ring (LCSR) and its brush section: wipe down the brushes, the brush holder, the ring itself, and the ring holder, then run a short powered rotation check to reach and clean the ring surface that sits under the brushes at rest. Use this task as preventive maintenance — it is the "just clean it" branch of slip-ring service. If a brush is already worn past the 2

Applies to
Activion16 (TSX-031A). No model- or revision-specific restriction is stated in source; applies to the gantry's large-current slip ring (LCSR) and its brush section.
Personnel
1 technician · "Field service engineer (CT gantry, basic mechanical/electrical service — comfortable cycling distribution-board breakers and briefly running the gantry in local mode from the maintenance panel with covers off); wear respiratory PPE (protective mask) for carbon/metal brush dust"
Steps
8 steps
Source
2D201-112EN*D §1.5.5 (pp.96–97) — Procedure for cleaning the large-current slip ring

Tools & parts

ItemPart numberQty
Sandpaper—1 sheet
Rag—Adequate amount

Safety

DANGER

Hazard: Touching the slip ring or brushes while the distribution-board breakers are energized

Consequence: Electric shock — high voltage is present in the slip ring and the brush section

Avoidance: Turn OFF ALL breakers on the distribution board before touching the slip ring or brushes, and keep them off for every step of this task that involves contact — power is deliberately restored only for the brief, hands-off rotation check in Step 6

CAUTION

Hazard: Incorrect slip-ring-brush cleaning technique — sandpaper used on the brushes, force applied to the ring while removing covers, rough brush handling, abraded powder left to fall into the gantry, brushes mounted off-center, or the cable left unverified

Consequence: Abnormal brush wear, ring damage, brush breakage, gantry contamination, or a bad electrical connection

Avoidance: Remove burrs from the brushes with a cutter ONLY — never sandpaper; use sandpaper only on the ring; never force or damage the ring when removing a cover; handle the fragile brushes gently; keep abraded powder out of the gantry; center the brushes on the ring at remount; verify the cable connection

CAUTION

Hazard: Powering the gantry ON with the slip ring/brush section exposed for cleaning (Step 6) and then touching it

Consequence: Electric shock

Avoidance: Never touch the slip ring, brushes, or related hardware once power has been supplied to the gantry — Step 6 is a hands-off rotation check only

CAUTION

Hazard: Wiping the remaining, previously-covered slip-ring sections (Step 7) without confirming the gantry is actually powered OFF

Consequence: Electric shock

Avoidance: Confirm the gantry power is turned OFF securely before wiping the sections not yet cleaned

CAUTION

Hazard: Cleaning the brush and brush holder while the brush holder is still mounted in the gantry

Consequence: Abraded material left on the brush holder can cause electrical discharge

Avoidance: Always remove the brush holder (Step 2) before cleaning the brush and brush holder (Step 3) — never clean them in place

Full step-by-step for Clean the large-current slip ring

All 8 steps are documented in the FSELIB Activion16 (TSX-031A) service manual — re-authored, web-first, with the real figures from the source.

7-day free trial · no credit card required

Related Power guides

View all Activion16 (TSX-031A) guides

Related error codes

Source: 2D201-112EN*D §1.5.5 (pp.96–97) — Procedure for cleaning the large-current slip ring. Preview re-authored by FSELIB — the full procedure with figures and steps is in the paid service manual.

“That they may see, and know, and consider, and understand together, that the hand of the LORD hath done this.”Isaiah 41:20