Skip to main content
ProcedureDASReplacement/FRUReplace

Replace the DAS PWB (Converter-16 / Control-16)

Remove and remount a printed wiring board (PWB) inside the DAS chassis on the Activion16 gantry — either a Converter-16 or the Control-16 PWB (or, on the CDAS-035A/2A generation, the equivalent AJ-CONVERTER / AJ-CONTROL PWB). The procedure is identical for both DAS generations and for either PWB type.

Applies to
Activion16 (TSX-031A). Covers both data-acquisition-section generations: CDAS-035A/1A (Converter-16 / Control-16 PWBs, §2.9.2, pp.204-205) and CDAS-035A/2A 'AJ' (AJ-CONVERTER / AJ-CONTROL PWBs, §2.17.2, pp.298-299) — the procedure text is identical between the two except for which PWB family is physically fitted. Confirm which generation is installed per §2.1 Introduction (toshiba-ct-activion16-das-reference-cdas-version-identification) before working.
Personnel
1 technician · Field service engineer (CT DAS / gantry electronics)
Steps
7 steps
Source
2D201-113EN*J §2.9.2 'Replacement of the DAS PWB (Removing and remounting a PWB)' (pp.204-205, CDAS-035A/1A) and §2.17.2 (pp.298-299, CDAS-035A/2A/AJ — verbatim repeat, nav-only in the coverage ledger, folded into this atom)

Tools & parts

ItemPart numberQty
Standard tool setn/a in source1 set
Antistatic matn/a in source1 (quantity not stated)
Clean glovesn/a in source1 pair (not stated as cotton in this section; §2.8.1 specifies cotton gloves for the same PWB-handling context)
Wrist band (antistatic/ESD wrist strap)n/a in source1
DAS PWB, replacement (Converter-16 or Control-16; AJ-CONVERTER or AJ-CONTROL for the CDAS-035A/2A generation)n/a in source — see Replacement Parts List (per §2.9.1/§2.17.1)1 (or more, per defective PWB(s))

Safety

CAUTION

Hazard: Opening the gantry front cover (step 1) without turning OFF the circuit protector switch

Consequence: The DAS remains ON (energized) even though the front cover is open — source does not spell out the resulting injury beyond "the DAS remains ON"; this precedes disconnecting system power in step (3) and directly handling PWBs in steps (5)-(6), consistent with the electric-shock rationale behind the general breaker-OFF policy (see DAS-W01/DAS-W02, related)

Avoidance: Be sure to turn OFF the circuit protector switch when opening the front cover of the gantry

NOTICE

Hazard: Touching the parts of the DAS PWB or its pattern (circuit) surface with hands or another object while replacing it (step 6), or soiling it with oil, water, etc.

Consequence: The SD (a DAS channel image-quality/noise metric named elsewhere in this manual's DAS troubleshooting sections, e.g. §2.8.5/§2.8.6, but not spelled out in this section) may be made worse

Avoidance: Be careful not to touch the parts of the DAS PWB or the pattern surface with your hands or other objects

Full step-by-step for Replace the DAS PWB (Converter-16 / Control-16)

All 7 steps are documented in the FSELIB Activion16 (TSX-031A) service manual — re-authored, web-first, with the real figures from the source.

7-day free trial · no credit card required

Related DAS guides

View all Activion16 (TSX-031A) guides

Related error codes

Source: 2D201-113EN*J §2.9.2 'Replacement of the DAS PWB (Removing and remounting a PWB)' (pp.204-205, CDAS-035A/1A) and §2.17.2 (pp.298-299, CDAS-035A/2A/AJ — verbatim repeat, nav-only in the coverage ledger, folded into this atom). Preview re-authored by FSELIB — the full procedure with figures and steps is in the paid service manual.

“That they may see, and know, and consider, and understand together, that the hand of the LORD hath done this.”Isaiah 41:20