Skip to main content
ProcedureGantrySoftware/UtilitiesMeasure

Operate the KGTSM maintenance panel

Use the KGTSM maintenance panel's built-in switch bank to run a single gantry/couch function directly on the bench — wedge, DAS test, slit, detector, tilt, test rotation, scanoscope, scan, projector lamp, couch slide, couch height, offset, slide idle/zero-clear, or rotor brake — without going through the operator panels or the console. This is the direct-hardware path used for service checks and a

Applies to
Activion16 (TSX-031A) gantry fitted with the KGTSM maintenance panel (physical switch bank SW1/SW11/SW12/SW21/SW31/SW32 and indicators LED66/LED67). A PC/Hyper Terminal equivalent exists (§3.5.3) and is covered in a separate atom.
Steps
7 steps
Source
2D201-112EN*D §3.5.1 'Important notices' + §3.5.2 'Procedures to use the maintenance panel' (p.211–215)

Safety

NOTICE

Hazard: Panel switch SW1 set to ON

Consequence: the KGTSM maintenance panel takes exclusive control — the gantry/couch cannot be operated from the operator panels or from the console while SW1 is ON (functional interlock, no injury risk)

Avoidance: Treat SW1-ON as taking over normal control; return SW1 to PANEL OFF (Work procedure step 6) as soon as maintenance-panel work is finished (source §3.5.1 item 1)

NOTICE

Hazard: SW1 turned ON while the gantry or couch is already in motion

Consequence: the gantry or couch stops; the gantry stops rotating at the TUBE home position (tube position -15°)

Avoidance: Expect an abrupt stop at the TUBE home position if SW1 is switched ON during motion; do not toggle SW1 mid-motion unless that stop is intended (source §3.5.1 item 2)

NOTICE

Hazard: Slide-out movement commanded from the maintenance panel with the couch already closer to the OUT end than the OUT-2 position

Consequence: the couch slows down and stops, triggered by the built-in safety function

Avoidance: Anticipate the automatic slowdown/stop near OUT-2 when driving slide-out from the panel; do not mistake it for a malfunction (source §3.5.1 item 3)

NOTICE

Hazard: Panel switch SW1 turned OFF before the indicated/selected operation has terminated

Consequence: the operation in progress may be interrupted or left in an unintended state

Avoidance: Wait for the selected operation to finish before setting SW1 to PANEL OFF (source §3.5.1 item 5)

NOTICE

Hazard: PANEL switch (SW1) turned OFF before the SET switch (SW11) — and the SCAN switch (SW12), where used — is released

Consequence: per source footnote *2, the panel-off transition is not clean

Avoidance: Release SW11 (SET) and SW12 (SCAN) first, then set SW1 to PANEL OFF

NOTICE

Hazard: SW32 (FUNCTION SET) changed while a function selected on it is still being carried out

Consequence: unpredictable behavior of the function in progress (source footnote *1)

Avoidance: Do not change SW32 while its selected function is running

NOTICE

Hazard: KGTSM not reset after maintenance-panel use

Consequence: the system may remain in a maintenance-panel-influenced state

Avoidance: Always press RESET (SW21) or cycle power after finishing (Work procedure step 7; source §3.5.1 item 4 and footnote *3)

Full step-by-step for Operate the KGTSM maintenance panel

All 7 steps are documented in the FSELIB Activion16 (TSX-031A) service manual — re-authored, web-first, with the real figures from the source.

7-day free trial · no credit card required

Related Gantry guides

View all Activion16 (TSX-031A) guides

Related error codes

Source: 2D201-112EN*D §3.5.1 'Important notices' + §3.5.2 'Procedures to use the maintenance panel' (p.211–215). Preview re-authored by FSELIB — the full procedure with figures and steps is in the paid service manual.

“That they may see, and know, and consider, and understand together, that the hand of the LORD hath done this.”Isaiah 41:20